Imagine you’re fishing with so much excitement, but suddenly your excitement turns into sorrow when you find your fishing rod is broken.
Basically, fishing rods are durable and last a long time. but it’s not always possible to keep it intact.
It can easily break while you’re fighting with a fish. just because it’s broken don’t throw it away, try to fix it for future use and save your money without spending on a new one.
This article will guide you with some easy steps on how to fix a broken fishing rod so that you can fix it on your own and can reuse it for future fishing trips.
Tools Needed To Fix the Broken Fishing Rod
There are a few basic tools that are necessary to get the job done. You can collect them from a hardware store.
- Sandpaper
- Tape measure
- Fiberglass pole
- Paintbrush or toothbrush
- Epoxy
Things To Remember During Fixing Fishing Rod
When repairing a fishing rod, try to keep it neat and clean. Tidy up any epoxy splatter.
-If you find that the epoxy has gotten on the tip of your fingers, rub the area with a cotton swab. This will remove it easily.
-Avoid using too much epoxy. If you find that an area of the rod has been exposed, cover it with a layer of epoxy and allow it to dry.
–If you are repairing a graphite rod, remember to add some graphite dust to the epoxy.
Epoxy is white, so if it is not mixed with graphite dust, it will look stained and dirty.
-Also, if you have graphite dust on the tip of your fingers and it gets on the epoxy, it will look like dirt.
Apply a little more epoxy and wipe off the excess with a paper towel.
How To Fix A Broken Fishing Rod?
Fixing a broken fishing rod is not difficult, but it can be a bit tedious. Just follow these simple tips and you can easily fix it.
Step-1) Prepare Materials
Sandpaper, tape measure, fiberglass pole, and paintbrush or toothbrush. Select the proper amount of sandpaper to be used.
Sandpaper is available in various grades, so you must select it according to your fishing rod’s condition.
Remove any rust and dirt that could be on your fishing rod. Dry the pole with paper towels and clean it thoroughly.
Step-2) Understand the Damaged Area of the Fishing Rod.
Take some time and understand the damaged area. It is important to know the location of the broken part.
The damaged area might be at the tip or on the main shaft. Take your time and do it properly.
Take note of where the broken part is located and prepare a piece of sandpaper for that repair.
Step-3) Smoother the Fishing Rod
The harder the sandpaper is, the smoother the fishing rod will become. Do not use any chemical-based cleaner.
Also, avoid using soap and water to clean the damaged area. Remove the damaged area by smoothing it with sandpaper.
The use of sandpaper is very effective in fixing a broken fishing rod.
Step-4) Use Fiberglass
Use tape and measure the broken rod ends, then cut a piece of fiberglass thinner than your fishing road.
Then Slide the fiberglass inside the fishing rod at approximately 15 centimeters.
Check the area around the broken ends to ensure that no part of the rod is left unglued or visible.
Step-5) Apply Epoxy Glue
Use a paintbrush or toothbrush, and epoxy at the end of the exposed side of the fiberglass pole.
You can buy it from any hardware store. Before applying the epoxy glue, make sure the rod is dry. The epoxy glue may not stick to a wet fishing rod.
Step-6) Attach Another Broken Part
Now take the rest of the broken part and slide it into the fiberglass. Let it dry overnight.
Check the area around the broken end to ensure that no part of the rod is left unglued or visible.
Step-7) Wrap the Break Area with a Winding Thread
After drying the broken rod with epoxy glue, Wrap the end of the rod with a winding thread.
It is essential to make sure that it is tight and sturdy. This should help prevent breakage, and make the rod stronger.
FAQs
What is the best way to repair a broken carbon fiber rod?
The best way to repair a broken carbon fiber rod is first to use epoxy glue on the end of the rod.
This will make the rod stronger. Next, wrap the area with a winding thread, and then place epoxy glue over that.
How do you replace a rod tip insert?
There are two ways to replace a rod tip insert. One is to use epoxy glue, and the other is to use epoxy glue and fiberglass cloth.
The fiberglass cloth will glue down the insert, while the epoxy glue will hold it in place.
How do you remove epoxy glue from a carbon fiber rod?
To remove epoxy glue from a carbon fiber rod. First, use acetone to soften the glue. Next, soak the area with water for 1-2 minutes.
Finally, use an acetone-soaked rag to wipe the area. Once the epoxy glue is removed, wash the area with acetone-soaked water.
Once dry, apply a thin coat of epoxy glue to secure the insert.
What are the advantages of using carbon fiber rod inserts?
Carbon fiber rod inserts are lightweight and offer a very stiff structure. They also resist wear and tear, resulting in a longer life span for the rod.
What is the maximum weight limit for a fishing rod?
Most expert anglers recommend that the lightest rod can hold no more than 1.64 ounces; the heaviest is 1 ounce. Between these points, the rate varies according to the fishing line.
What is the difference between a graphite and carbon fiber rod?
Graphite is brittle, while carbon fiber is more flexible. Carbon fiber also has greater tensile strength. This means it can be stronger than graphite.
How does the rod absorb shock?
When you cast a line, the rod absorbs some of the energy from the force. The shock is then transferred to the lure.
If you want to reduce the amount of shock, use a rod that is lighter in weight. The less mass there is in the rod, the less energy it will absorb.
How long will a fishing rod last?
It depends on how often you use it and how much strength you put into it. The more strength you put into it, the less time a rod will last.
It is recommended to replace your fishing rod every two years, regardless of how much strength you put into it.
If you use a graphite rod, do not expect it to last more than five years.
Are graphite fishing rods harmful?
Graphite is not harmful to human health. However, you should always keep in mind that the more strength you put into it, the less time a rod will last.
Are graphite rods better than fiberglass rods?
Graphite rods are lighter and more sensitive, which makes them easier to use. Fiberglass rods are heavier and do not feel as sensitive as graphite ones.
What’s the difference between a fishing rod and a fishing pole?
A fishing rod is a piece of actual equipment used to cast a line. A fishing pole is a tool used by anglers to carry their equipment while they are on the water.
It is made of fiberglass and has an adjustable length.
Why is having a strong line rod necessary?
To have a strong line is very important. The stronger the line, the more you will enjoy fishing and the longer your enjoyment time will be. If the line is too you may lose the fish
What is the best type of fishing line?
The best type of fishing line is one with a high percentage of mono. This is because it has good strength, sensitivity, and durability when it comes to knots.
How do you cast a fishing rod?
To cast a fishing rod, simply tap on the screen and then drag it through the water. You can adjust your cast by holding it down on one side of the screen. Hold it for as long as you need to make your cast.
What should you look for in a fishing reel?
A good fishing reel should have a high percentage of carbon fiber in it. This is because it will make the reel strong, lightweight, and durable. It is also a very good idea to use a line counter on your reel.
Conclusion
Fishing rods are the most important equipment for fishing. A fisherman has a personal attachment to it, which makes it worth their investment. it’s really heartbreaking when it is broken, especially at the time of fishing.
So through this article, I tried to guide you with some easy steps on how to fix a broken fishing rod.
So my suggestion is not to lose your hope, and don’t stop fishing, just because it’s broken. carefully follow these steps, repair it and go for another exciting fishing trip.